1 c4d10120d silicon carbide schottky diode z -r ec ? r ectifier features ? 1.2kv schottky rectifer ? zero reverse recovery current ? high-frequency operation ? temperature-independent switching ? extremely fast switching benefts ? replace bipolar with unipolar rectifers ? essentially no switching losses ? higher effciency ? reduction of heat sink requirements ? parallel devices without thermal runaway applications ? switch mode power supplies ? power factor correction ? motor drives package to-247-3 maximum ratings (t c =25c unless otherwise specifed) symbol parameter value unit test conditions note v rrm repetitive peak reverse voltage 1200 v v rsm surge peak reverse voltage 1300 v v r dc peak reverse voltage 1200 v i f continuous forward current (per leg/device) 19/38 9/18 5/10 a t c =25?c t c =135?c t c =160?c i frm repetitive peak forward surge current 26* 18* a t c =25?c, t p =10 ms, half sine pulse t c =110?c, t p =10 ms, half sine pulse i fsm non-repetitive forward surge current 46* 36* a t c =25?c, t p =10 ms, half sine pulse t c =110?c, t p =10 ms, half sine pulse i f,max non-repetitive peak forward current 400* 320* a t c =25?c, t p =10 m s, pulse t c =110?c, t p =10 m s, pulse p tot power dissipation(per leg/device) 93/187 40/81 w t c =25?c t c =110?c t j operating junction range -55 to +175 ?c t stg storage temperature range -55 to +135 ?c to-247 mounting torque 1 8.8 nm lbf-in m3 screw 6-32 screw * per leg, ** per device part number package marking c4d10120d to-247-3 c4d10120 v rrm = 1200 v i f ( t c =135?c) = 18 a ** q c = 54 nc ** c4d10120d rev. f
2 electrical characteristics (per leg) symbol parameter typ. max. unit test conditions note v f forward voltage 1.4 1.9 1.8 3 v i f = 5 a t j =25c i f = 5 a t j =175c i r reverse current 20 40 150 300 a v r = 1200 v t j =25c v r = 1200 v t j =175c q c total capacitive charge 27 nc v r = 800 v, i f = 5a d i /d t = 200 a/s t j = 25c c total capacitance 390 27 20 pf v r = 0 v, t j = 25c, f = 1 mhz v r = 400 v, t j = 25?c, f = 1 mhz v r = 800 v, t j = 25?c, f = 1 mhz note:this is a majority carrier diode, so there is no reverse recovery charge. thermal characteristics symbol parameter typ. max. unit test conditions note r jc thermal resistance from junction to case 1.6* 0.8** c/w * per leg, ** per device typical performance (per leg) 0 1 2 3 4 5 6 7 8 9 10 0 0.5 1 1.5 2 2.5 3 3.5 current (a) voltage (v) figure 1. forward characteristics figure 2. reverse characteristics 0 100 200 300 400 500 600 700 800 900 1000 0 500 1000 1500 2000 current (a) voltage (v) t j =-55c t j = 25c t j = 75c t j =125c t j =175c t j =-55c t j = 25c t j = 75c t j =125c t j =175c i f (a) v f (v) i r (a) v r (v) c4d10120d rev. f
3 25 30 35 40 45 50 55 60 if(peak) peak forward current (a) c4d10120d per leg current derating 0 5 10 15 20 25 25 50 75 100 125 150 175 if(peak) peak forward current (a) tc case temperature (?c) figure 3. current derating figure 4. power derating 0.0 10.0 20.0 30.0 40.0 50.0 60.0 70.0 80.0 90.0 100.0 25 50 75 100 125 150 175 figure 5. recovery charge vs. reverse voltage figure 6. capacitance vs. reverse voltage typical performance (per leg) 0 50 100 150 200 250 300 350 400 450 0.1 1 10 100 1000 0 5 10 15 20 25 30 35 0 200 400 600 800 1000 t c i f(peak) (a) p tot (w) t c qrr (nc) v r (v) c (pf) v r (v) 10% duty 20% duty 30% duty 50% duty 70% duty dc c4d10120d rev. f
4 6.0 8.0 10.0 12.0 14.0 capacitive energy (uj) 0.0 2.0 4.0 0 200 400 600 800 1000 e c capacitive energy (uj) v r reverse voltage (v) typical performance 100 1000 i fsm (a) 10 1.e-05 1.e-04 1.e-03 1.e-02 tp(s) 1000 100 10 figure 7. typical capacitance stored energy, per leg figure 8. non-repetitive peak forward surge current versus pulse duration (sinusoidal waveform), per leg t p (s) i fsm (a) t j = 25c t j = 110c v r (v) 14 12 10 8 6 4 2 0 0 200 400 600 800 1000 e c ( m j) 1e-05 1e-04 1e-03 1e-02 figure 9. device transient thermal impedance 1e - 3 10e - 3 100e - 3 1 1e - 6 10e - 6 100e - 6 1e - 3 10e - 3 100e - 3 1 junction to case impedance, z thjc ( o c/w) time, t p (s) 0.5 0.3 0.1 0.05 0.02 0.01 singlepulse p cj t (sec) c4d10120d rev. f
5 part number package marking c4d10120d to-247-3 c4d10120 package dimensions package to-247-3 recommended solder pad layout to-247-3 t u w v pos inches millimeters min max min max a .190 .205 4.83 5.21 a1 .090 .100 2.29 2.54 a2 .075 .085 1.91 2.16 b .042 .052 1.07 1.33 b1 .075 .095 1.91 2.41 b2 .075 .085 1.91 2.16 b3 .113 .133 2.87 3.38 b4 .113 .123 2.87 3.13 c .022 .027 0.55 0.68 d .819 .831 20.80 21.10 d1 .640 .695 16.25 17.65 d2 .037 .049 0.95 1.25 e .620 .635 15.75 16.13 e1 .516 .557 13.10 14.15 e2 .145 .201 3.68 5.10 e3 .039 .075 1.00 1.90 e4 .487 .529 12.38 13.43 e .214 bsc 5.44 bsc n 3 3 l .780 .800 19.81 20.32 l1 .161 .173 4.10 4.40 ?p .138 .144 3.51 3.65 q .216 .236 5.49 6.00 s .238 .248 6.04 6.30 t 9? 11? 9? 11? u 9? 11? 9? 11? v 2? 8? 2? 8? w 2? 8? 2? 8? note: recommended soldering profles can be found in the applications note here: http://www.cree.com/power_app_notes/soldering c4d10120d rev. f
6 6 diode model t t t r if v vf * + = note: t j is diode junction temperature in degrees celsius r t = 0.08 + ( t j * 8.5*10 -4 ) v t = 0.96 + ( t j * - 1.22*10 -3 ) note: t j = diode junction temperature in degrees celsius, valid from 25c to 175c c4d10120a rev. f copyright ? 2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree, the cree logo, and zero recovery are registered trademarks of cree, inc. cree, inc. 4600 silicon drive durham, nc 27703 usa tel: +1.919.313.5300 fax: +1.919.313.5451 www.cree.com/power ? rohs compliance the levels of rohs restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with eu directive 2011/65/ec (rohs2), as implemented january 2, 2013. rohs declarations for this product can be obtained from your cree representative or from the product documentation sections of www.cree.com. ? reach compliance reach substances of high concern (svhcs) information is available for this product. since the european chemi - cal agency (echa) has published notice of their intent to frequently revise the svhc listing for the foreseeable future,please contact a cree representative to insure you get the most up-to-date reach svhc declaration. reach banned substance information (reach article 67) is also available upon request. ? this product has not been designed or tested for use in, and is not intended for use in, applications implanted into the human body nor in applications in which failure of the product could lead to death, personal injury or property damage, including but not limited to equipment used in the operation of nuclear facilities, life-support machines, cardiac defbrillators or similar emergency medical equipment, aircraft navigation or communication or control systems, or air traffc control systems. notes
|
